WEN10703 1 in. Precision Dial Indicator with .001 in. Resolution

I can't believe the quality and appearance of this indicator for the price. WEN is absolutely killing it! I am a machinist and have purchased a WEN 1/8" variable speed die grinder, a variable speed detail file sander, and now this dial indicator. All of them are solid and don't feel the least bit cheap. I tested the dial indicator on calibrated gage blocks from .050" to .750" and it was well within its accuracy range. The case and bezel are very impressive and all move freely. Great job WEN!

Works as intended 👍

I bought two of these to try out. For the two that I received the bezels were extremely tight, and would be useless in practice. But I took them apart by removing the faceplate and saw that there are two spring clamps holding down the bezel. I loosened the clamp screws and the bezels turned freely. I then put some Loctite on the loosened screws to keep them in place, and then re-assembled. Both units work fine now. Accuracy and repeatability are fine out the box. Movement of the shaft is smooth. I ordered two more. I'm using them to make locating fixtures for my mill and lathe. If not dropped or otherwise abused I don't see why they wouldn't last a long time, but time will tell. But for the price, these units are a great value.UPDATE: I received my 2 additional indicators. Same problem with the bezels, but I repeated the fix and they're good to go as well. These units are better than the ones I bought from Harbor Freight for $18. If you want to fix the bezel yourself here's what you need to do:1. Looking at the indicator face, use a dental pick and insert it the space between the top retaining ring. GENTLY work out the top retaining ring (which also serves as a rotatable index) towards the center of the face. There are two retaining rings (indexes), one on top of the other. GENTLY work it out of the slot it resides in, being careful not to bend it and permanently deform it.2. Repeat for the lower ring.3. The clear plastic lens will now drop out if you turn the indicator over. Note that the lens is convex or dome shaped.4. With the pick, remove the white beveled ring. Note its orientation so that you replace it properly.5. With the pick, lift up the graduated face plate. It has a tiny tab somewhere on its edge which holds it in place. Gently lift the faceplate until it is just underneath the needle. Now you have to very gently pull up on the tip of the needle to lift up the faceplate enough to remove it from the housing.6. You can now see two spring clamps on the outer edge held down by a small phillips-head screw.7. Remove both screws.8. Put some blue Loctite on the screws and re-install just to point where the bezel starts sticking, then back-out a 1/4 turn.9. Re-assemble in reverse order, being sure that the white beveled ring and lens are in the proper orientation. If the plunger sticks when re-assembled the lens is probably upside-down. If the needle moves when you rotate the bezel, then the needle may have been bent upwards when removing the faceplate and it is dragging. Just disassemble again, removing the retaining rings and lens only. Then put a very small screwdriver under the needle and push down on the needle tip, using the screwdriver as a fulcrum. The needle should not touch the dial or lens.10. Verify operation of the bezel and plunger motion.11. Now you have a very good $15 indicator.

Good quality tool for a reasonable price. Used to measure piston quench and crankshaft end play . Use a magnetic mount.

well made

I rarely review anything on Amazon. The second I picked the box up for this I was shocked at the weight of it. After unboxing it, I couldn't believe how nice the thing was for the money. I mounted my dial indicator on it but have not used it for a project yet, but I am quite confident it will work as intended. I am very impressed to say the least. I won't speak for folks using these daily, but for a hobbiest like myself, I would bet it will last a lifetime based on what I see

Best gauge I have found to date for the price, actually returns to zero setting when others failed.

Good enough low cost device