HueparLaser Detector for Laser Level, Detect Green & Red Beams Digital Laser Receiver Compatible with Huepar Pulse Mode Line Laser Level Up to 200Ft, Three-Side LED Display, Clamp Included

Incredible! I have owned my Huepar GF360G laser level for almost 3 years now. It is one of my absolutely most favorite tools that I use professionally. It is robust, accurate, and affordable. I have just added this Huepar laser detector for out door work and…. holy crap!! It is AMAZING. My buddy has a close to $1000 laser transit system from Bosch. This Huepar detector and my standard 3 plane Huepar laser level (gf360g) is now BETTER than his for layouts. Mind blowing. This detector’s ability to be used vertically or horizontally wit witness marks for each and side LEDs for easy reading has been just awesome! This has completely upped my game and I couldn’t be happier with this detector and my laser level from Huepar.

This works perfectly with the Huepar laser generator using pulse mode, and is definitely needed if using the laser during daylight hours. Haven't tested it past 50 ft yet, but works great to that range.

The sensor on the Front is great and easy to use if you follow the directions in the meager booklet and play with it a while. Like so many products from you-know-where the instructions are less than what you want. Make sure the sending unit is in pulse-mode.The sensors on the side and back either work intermittently or I am not using them correctly. I really don't need them but I wished they did work better. I am tempted to return it for a replacement.Good luck.

I used this to level a cripple wall on a foundation. The sun was bright so it was impossible to see the laser line past 10 feet even with a reflector, but with this device, I could level the wall out perfectly. This has saved me so much time. It is well worth the money! My new favorite toy!

I bought an LR-6RG when I bought my SO4CG some years ago. I’m a diy’er. I’m now getting ready to level my foundation. The LR6RG doesn’t detect the laser I just bought a new LR-6RG to double check and the new one doesn’t work with the SO4CG either. You’ll have to spend a little more money. Get a Bosch or a Dewalt. This setup DOES NOT WORK even though huepar says my items work together. What a big disappointment

The media could not be loaded. I just got this detector and Huepar 503CG laser level to use outdoors building screen rooms patio covers and pool enclosures.Most of what I do is in the bright sun and no laser level can really be seen beyond a short distance. This detector solves that problem if you use it with a compatible green laser with pulse mode.Some reviews have said it's too sensitive and it's hard to get it to the solid tone lining up with the laser. I've seen that complaint about all detectors. It's not a problem with the detector. These are sensitive down to a small fraction of an inch. If you're not able to hold it at that it's not going to tone in. I was able to find the beam and get it to tone in easily at about 70 ft just holding it in my hand. I didn't test beyond that. ANY detector takes a steady hand and a little bit of practice to use precisely. The fact is most people don't need that level of precision for what they might be doing at those distances. If you can get it to beep on either side you'll still be within a small fraction of an inch.It also has to be a certain distance away from the laser level. It's not far but if you try testing it at a few inches it's not going to work properly. That also goes with any detector.This has to be used with a green laser that has"pulse mode" and pulse mode has to be turned on. I'm sure at least some of the negatives are from people using it with the wrong laser or using it incorrectly.The beeping is very loud. It can be turned off but there are no volume settings. You can comfortably hold it with your thumb over the speaker and that makes a big difference but I wish it had a volume control. I'll probably put a piece of tape over the speaker. I wouldn't reduce a star for it because it's not sold as having a volume control. I'd rather it be too loud than too quiet as there are times where you might want to set the detector in place and move the laser from a distance and listen for the tone.I also like that it has LED indicators on the front, the back, and one side. That's a feature a lot of high-end detectors don't even have. That's handy and a tight area, working on a ladder or some other position where you can't comfortably see the front of it.

I have a Huepar laser level and I read the reviews to see that laser level must be set to pulse mode for the receiver to work properly. This worked perfectly for our project. It was very accurate and helpful when bright light makes laser line difficult to see or when checking level without looking.

After my Bosch laser level died I started looking for a new laser level. What was important was accuracy, size off the laser over 50’,and battery life. With the job fast approaching I decided on the Huepar 3D green beam Pulsing Line Laser with and sensor.Receiving it the day before the job started I turned it on at home and read the directions. Unfortunately the detector did not arrive with the laser.The next day at the job was a complete BUMMER as the line could not be seen past 4’ in bright sunlight! Checking my Amazon order I found the detector had been delivered to my home.DAY 2 at the job. My laborer with maybe an hour of working with the laser and detector was able to level and shim the piers for a 925 sq. ft. floor!!!The center beam for the floor is 38’, the diagonal of the floor a round 45’. The pluse sensor worked like a charm.The pulse laser with sensor was well worth the purchase!